Screw Oil Press 20–500 kg/h | Cold Press, 304 Stainless

A screw oil press that works at the scale real oil producers work at.

Most oil presses sold in Southeast Asia are either 5 kg/h household units or million-dollar industrial lines. Nothing sits in between — and that middle band is where small oil workshops, cooperatives and coconut processors actually live. This press covers 20–500 kg of raw material per hour, runs continuously, and is built in food-grade 304 stainless from the hopper to the oil outlet.

Built for peanut oil in the central provinces, sesame oil in the southeast, and virgin coconut oil in Ben Tre. Configured for 220V or 380V, 50 or 60Hz before it leaves the factory.

Four stages, continuous, no batch loading.

Feed — Cleaned oilseed enters the hopper through a variable-speed feeder. Feed rate is the main control for pressing pressure.

Compress — A tapered screw shaft rotates inside a hardened cage. Root diameter increases and pitch narrows toward the outlet, so pressure builds progressively along the barrel instead of in one hit.

Separate — Oil drains through the cage slots into a collecting tray under the barrel. Cake continues forward, squeezed drier as the channel narrows.

Discharge — Cake exits through an adjustable back-pressure cone. The gap setting balances yield against cake dryness — tighter gap means more oil out, but higher motor load and warmer oil.


Three components that decide the result

① Tapered screw shaft
The single part that determines how much oil you get. Root diameter grows and flight pitch shrinks toward the discharge end, building pressure in steps. Shaft hardness and flight geometry are what separate a press that runs for years from one that wears out in months.

② Press cage (barrel)
Slotted 304 stainless cage, slot width matched to your oilseed. [ ] mm standard, other widths available. Oil flows out through the slots while cake is retained. Quick-release design — the cage opens without pulling the shaft, so cleaning between batches takes minutes, not hours.

③ Adjustable back-pressure cone
Spring or handwheel loaded discharge head. Gap of [ ] mm sets the balance between yield and residual oil. Different oilseeds need different gaps — this is the adjustment operators make most often, so it is designed to be changed without tools.


Cold press or hot press?

The question every buyer asks first. It is a process decision, not a machine limitation — the same press handles both, with different upstream preparation.

Practical note for Vietnamese producers: traditional peanut oil sells on aroma, not just yield. If your product is dầu phụng for the domestic market, plan for a roasting step upstream — a cold press alone will give you oil that tests clean but does not taste like the product your customers know.

Why buy from ZKING

Direct factory, no trading layer. 11,000 m² in-house workshop with CNC machining, sheet-metal laser cutting and electrical assembly. The press cage and screw shaft are machined in-house, not outsourced — which is why we can supply replacement shafts and cages for years after delivery.

Tested with your material, not ours. Send 1–5 kg of your oilseed. We run it on the actual machine, record yield, residual oil and oil temperature, and send you the video and the parameters within 3–5 days. Free of charge.

48-hour full-load test before shipment. Every unit runs 48 hours on real material before it is packed. You get the test record with the machine.

Built for Southeast Asian conditions. 220V/380V, 50/60Hz set at factory. High-humidity motor and electrical protection. English manual plus Vietnamese [ if available ] operating documents.

Spare parts and support in the region. Wearing parts — screw shaft, cage, cone — stocked for fast dispatch. Remote commissioning support by video and Zalo. On-site installation available by region, quoted separately.

Honest delivery window. Standard models 30–45 days, custom configurations 60–90 days, sea freight to your nearest port with anti-rust packing and full export documents (C/O, packing list, commercial invoice).


FAQ

What oil yield can I expect?
Depends on your oilseed and moisture content. Peanut kernels typically run [ ] %, sesame [ ] %, coconut copra [ ] % on our press under standard settings. Send a sample and we will give you a measured figure, not a brochure number.

How much oil is left in the cake?
[ ] % under standard gap setting. Tighter gap lowers residual oil but increases motor load and oil temperature — we set the factory default for your oilseed and show you how to adjust it.

Do I need to roast the seed first?
Only if you want roasted aroma. Cold press works with cleaned seed directly. For traditional peanut and sesame oil, a roasting step is recommended — we can quote a roaster matched to your press capacity.

Can it run continuously?
Yes. Continuous feed, continuous cake discharge. For 8-hour shifts the only stops are filter cleaning and routine checks.

Is the oil ready to bottle straight from the press?
No. Pressed oil carries fine sediment and needs settling or filtration. A filter press or settling tank is part of the recommended configuration — we will spec it with the press so you are not stuck at the bottling stage.

What about food safety certification?
The machine is built from food-contact 304 stainless and supplied with material certificates. For edible oil production in Vietnam you will need Giấy chứng nhận ATTP (food safety certificate) for your facility — that is a producer-side requirement, and we can provide the equipment documentation your application needs.


CTA

Send us your oilseed — we will run it and tell you what you get.

Tell us: the oilseed, your target kg per hour, and whether you want cold press or roasted. We reply within 24 working hours with the recommended model, a measured yield estimate and a price.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top